Description
Interlux Nautical ProGuard Ablative Antifouling Paint
Interlux Nautical ProGuard Ablative is performance, value and reliability all in one. ProGuard Ablative is an all-purpose, low V.O.C. antifouling paint formulated to erode away with use reducing paint build-up. ProGuard Ablative provides season-long protection in moderate to high fouling waters and can be applied directly over most properly prepared antifouling paints. Recommended for use on the underwater areas of fiberglass, wood, and properly primed metal (except aluminum) boat hulls and can be used in fresh, salt and brackish waters.
- Reliable performance at an excellent value
- Reduced paint build-up
- Season-long protection in moderate to high fouling waters
- Compatible over most antifouling paints
- Low V.O.C.
Specifications:
- Finish: Matte
- Coverage: 455 sq. ft/gal
- Number of Coats: 2 coats, 3 on bare wood
- Application Method: Brush, roller, airless and conventional spray
Do not use on aluminum
***WILL SHIP GROUND ONLY TO THE CONTIGUOUS 48 STATES ONLY***
How to Apply
APPLICATION DATA METHOD: Airless Spray, Brush, Conventional Spray, Roller
NUMBER OF COATS: 2, 3 on bare wood
DRY FILM THICKNESS PER COAT: 2 mils (3.6 mils wet)
COVERAGE: 455 sq. ft/gal.
APPLICATION TEMP: 41°F Min. / 95°F Max.
THINNER: Thin 10% wuth Xylene. Do not exceed 10 % by volume.
| Temp | To Touch | To Recoat | To Launch |
| 95°F | 1 HR | 8 HR | 8 HR |
| 73°F | 2 HR | 12 HR | 12 HR |
| 50°F | 3 HR | 16 HR | 16 HR |
PREVIOUSLY PAINTED SURFACES - GOOD CONDITION: Remove all traces of loose paint by sanding the entire surface with 80 grit wet-or-dry sandpaper; wipe surface clean with Xylene¹ using the two-rag method before and after sanding. Apply two coats of ProGuard Ablative allowing for appropriate dry times.
PREVIOUSLY PAINTED SURFACES - POOR CONDITION: Completely remove old antifouling paint, after all old antifouling paint has been completely removed, sanding the entire surface with 80 grit wet-or-dry sandpaper; wipe surface clean with Xylene¹ using the two-rag method before and after sanding. Apply two coats of ProGuard Ablative allowing for appropriate dry times.
BARE FIBERGLASS: scrub the surface thoroughly with a stiff brush using soap and water. Flush with fresh water to remove the soap residue and allow surface to dry. Remove mold release wax and surface contamination by wiping down the surface with Xylene¹ using the two-rag method. Fill any surface imperfections with approved filler for underwater use. Sand the entire surface with 80-grit sandpaper until a flat matte finish is obtained. Wipe the sanding residue off the surface with Xylene¹ using the two-rag method. Apply two coats of ProGuard Ablative allowing for appropriate dry times.
BARE WOOD: Sand the entire surface with 80 grit wet-or-dry sandpaper; wipe surface clean with Xylene¹ using the two-rag method before and after sanding. Apply the first coat of ProGuard Ablative thinned 10% with Xylene². Apply two finish coats of ProGuard Ablative allowing for appropriate dry times
UNDERWATER METALS: Apply an approved underwater metal primer as per manufacturer’s instructions. Apply two coats of ProGuard Ablative allowing for appropriate dry times. Do not use on aluminum
APPLICATION METHODS:
Specifications
- Hazardous Shipping:
- This item has D.O.T. Hazard Shipping Restrictions and cannot be shipped in the air. It can be ordered online for shipment by Ground Shipping Methods.
- Item may require Truck Shipping:
- Indicates an item that may only be available for shipment via LTL carrier (truck)
- California Residents:
- Cancer and Reproductive Harm - P65Warnings.ca.gov
- Paint Type:
- Ablative Antifouling
- Number of Seasons:
- Single Season
- Antifouling Type:
- Copper Based
- Hull Material:
- Fiberglass, Steel, Wood
- Water Type:
- Brackish Water, Fresh Water, Salt Water
